MPO Breakout & Harness Cable

MPO 8 Fiber OM4 to FC Breakout Cable

Specify an MPO 8 fiber OM4 to FC breakout cable for individual FC/UPC destinations. The supplied configuration combines one MPO-8/PC female end with eight FC/UPC branches, OM4 50/125 μm fiber and a violet jacket. Confirm the endpoint interfaces and eight-path mapping before ordering.

MPO Breakout & Harness Cable

Hero

Specify an MPO 8 fiber OM4 to FC breakout cable for individual FC/UPC destinations. The supplied configuration combines one MPO-8/PC female end with eight FC/UPC branches, OM4 50/125 μm fiber and a violet jacket. Confirm the endpoint interfaces and eight-path mapping before ordering.

Product Overview

This assembly is intended for an OM4 installation that needs to route eight fibers from a common MPO interface to separate FC/UPC ports. Its selection starts with the installed connector interface: FC destinations need the matching branch hardware and space to engage each threaded coupling. An LC branch is a different termination choice.

The supplied product definition identifies eight active fibers. It does not provide the MPO ferrule drawing or identify which fiber positions are populated. Ask for those details together with the viewing direction, key orientation and branch labels. “MPO-8” alone is insufficient to approve the connection map. Fluke Networks explains why active-fiber count and connector layout must be distinguished; that reference does not verify this product’s specific layout.

Use this product page to specify the FC configuration. For other connector families, browse the MPO breakout and harness range. For an architecture decision, use the breakout cable versus cassette comparison.

Key Features

  • One common MPO end and eight individually terminated FC/UPC branches in the supplied design.
  • OM4 50/125 μm fiber; violet jacket specified in the source material.
  • Female MPO interface specified; mating hardware and polish require drawing confirmation.
  • Separate branch labeling can be requested to match the destination port schedule; availability needs confirmation.
  • Overall length and fanout dimensions are selected against the route, with final dimensions recorded on an approved drawing.

Technical Specifications

Specification notice: This draft is for reference only; product-specific statements require approval. The following values reproduce the supplied design, rather than a signed production specification. confirmation with BWNFiber:all product-specific values and available configurations in this table.

ParameterSupplied design or required confirmation
Product familyMPO breakout / harness cable
Common endMPO-8/PC female (F), as named in the source
Active fibers8; populated positions and ferrule layout require a drawing
Branch ends8 × FC/UPC individual connectors
FiberOM4 multimode, 50/125 μm
Jacket colorViolet; match the accepted sample and BOM
Overall lengthSource lists 1–50 m; exact reference planes and tolerance to confirm
Fanout lengthSource lists 30 / 45 / 60 cm; no default is approved
Jacket optionsSource lists LSZH, OFNP and OFNR; exact construction and supporting documents to confirm
MappingSource lists Type A / B / C; use an approved eight-path connection table
Optical acceptanceInsertion loss and return loss limits, wavelengths, reference method and scope to confirm
Mechanical limitsBend radius, branch diameter, pulling limits and temperature range not supplied
ConformityNo product-specific certification or standards compliance is established by this attachment

Selection Guidance

Verify the FC destinations

Record the equipment or adapter model, fiber mode, connector interface and end-face requirement for each destination. FC/UPC is the specified branch termination. Do not approve a connection to an FC/APC interface by connector-family name alone. In this page, FC refers to the connector format; it is not a promise of Fibre Channel protocol or data-rate support.

Approve the eight-path map

Request a table with one row per active fiber: MPO position, viewing direction, branch identifier and destination port. Review that table against the full installed path, including any adapter, panel or intervening assembly. A Type A, B or C label does not replace the map, and eight branches do not by themselves establish four supported duplex data channels.

For the wider channel-design process, consult the MPO polarity checklist. Keep this product’s final position-to-FC assignment on its own drawing.

Compare the right alternatives

RequirementCandidateDecision boundary
Eight separate FC/UPC destinations on the specified OM4 pathThis supplied configurationConfirm all eight port interfaces and the drawing
LC destination portsAn LC-terminated harnessChoose a separate product; confirm simplex or paired branches
Single-mode FC routeAn OS2 FC assemblyDo not substitute OM4 based on connector appearance
OM3 installed routeAn OM3-compatible design reviewCheck the full link requirement before replacing any section
FC/APC destinationsA separately specified FC/APC assemblyDo not treat FC/UPC as an interchangeable order option

Check access and branch reach

Provide the FC port spacing and the available working clearance. Each connector must be reachable for connection, inspection and later maintenance. Measure the route to each destination and identify where the fanout must sit. A branch that can reach a port in a straight line may still be too short once routing and the approved bend allowance are included.

Applications

  • Equipment-room or test-fixture connections with confirmed OM4-compatible FC/UPC ports and an identified MPO interface.
  • Replacement assemblies where an existing eight-path schedule must be reproduced and traceable branch identification matters.
  • System-integrator or distributor BOMs that specify FC terminations separately from LC harness configurations.

These are selection scenarios, not BWNFiber customer cases. No 40G, 100G or SR4 compatibility is claimed for this assembly. A passive harness routes optical paths; equipment interfaces, the channel budget and the supported operating mode determine the application.

Order Guide

Send these details with the RFQ

RFQ fieldWhat to provide
Product referenceSource item 24 and the required drawing revision
Endpoint informationMPO mating interface plus all FC equipment or adapter references
Fiber assignmentEight rows linking MPO position, FC branch ID and destination port
LengthOverall length, reference planes, fanout position and each branch reach
Cable constructionRequired jacket classification, route constraints and installation market
AcceptanceRequired loss limits, test conditions, mapping checks and report format
Commercial scopeQuantity, destination, requested date, labels and packaging needs

Length reference

The source lists the following nominal metric lengths. Feet are approximate conversions, not separate order dimensions; the metric value should govern the drawing.

MetresApproximate feet
13.28
1.54.92
26.56
39.84
516.40
722.97
1032.81
1549.21
2065.62
2582.02
3098.43
40131.23
50164.04

The original 117-row list combines three mapping labels, three jacket labels and thirteen lengths. It is not evidence of 117 stocked or validated SKUs. Supported combinations and custom lengths require confirmation. Do not assume the source’s suggested order-code pattern is an approved part number.

Custom requests

Submit a branch-length schedule for staggered routing, a label schedule for destination identification, and any request for a different leg construction or pulling accessory. confirmation with BWNFiber:custom dimensions, 0.9 mm legs, pulling eyes, OEM labeling, sample availability, MOQ and lead time. Record accepted deviations on the quotation and drawing before ordering.

Quality and Acceptance

Ask for acceptance criteria that identify what is being tested: the connector interfaces, each completed optical path or the entire installed channel. An insertion-loss value without its test scope and reference method is insufficient to compare offers. Request the applicable wavelengths, test setup, limits, fiber identification and report traceability. Ask which return-loss checks apply to the accepted configuration rather than borrowing a single-mode limit for this multimode assembly.

The attachment mentions IEC and TIA references and RoHS, but contains no supporting conformity documents or test records. confirmation with BWNFiber:the applicable standards and editions, product scope, test methods, inspection evidence and any conformity statement. These references have therefore been removed from the compliance-claim field.

For repeat orders, compare the accepted drawing revision and any proposed component substitution. A visually similar replacement must still satisfy the approved interface, fiber map and installation requirements. Ask BWNFiber which records can accompany the quoted build; this request does not assert a testing or manufacturing capability that has not been documented.

Why Discuss This Build with BWNFiber?

A useful quotation for this configuration should resolve three FC-specific questions: whether the branch interfaces match the installed ports, whether all eight fiber destinations are correctly identified, and whether the branch geometry allows access for installation and servicing. Send those inputs with the quantity so the discussion starts from an identifiable assembly.

The existing breakout product family lists multiple connector options. Confirm which specifications apply to this exact OM4 FC build rather than carrying family-level performance figures into the order.

FAQ

Request an Assembly Review

Are eight FC connectors the same as four LC duplex connectors?

No. They are different connector arrangements. Select the branch termination to match the actual destination hardware and define any required fiber pairing separately.

Does FC mean Fibre Channel on this page?

No. It identifies the FC connector format. Protocol and data-rate compatibility must be established from the equipment and full optical channel.

Can these FC/UPC branches be ordered for FC/APC ports?

Do not approve that substitution. Obtain the exact mating requirement and request a separately specified assembly if an angled FC interface is needed.

What must an MPO-8 drawing show?

It should identify the ferrule layout, populated positions, viewing direction, key orientation, pinning and the connection to each FC branch. The supplied name does not contain that full definition.

Is Type B automatically the correct mapping?

No mapping is approved by this draft. Check the complete equipment-to-equipment path and the eight-row assignment table before choosing a mapping label.

Does the violet jacket prove the fiber grade?

Treat color as an identification aid. Verify OM4 from the accepted cable identification and product documentation, and match the final jacket color to the approved build.

Is this an SR4 breakout product?

No SR4 application is established for the supplied FC configuration. Validate the equipment ports, operating mode and fiber assignment independently before making such a claim.

Is 30 cm the standard branch length?

The source lists 30, 45 and 60 cm and mentions a default, but no approved drawing confirms one. Request the branch length required by the actual port layout.

Can I choose a jacket only from its name?

State the installation requirement and ask for documentation covering the quoted cable construction. The labels in the source are not proof of project acceptance.

What should I check for a replacement assembly?

Compare the connector interfaces, fiber grade, eight-path map, branch labels, overall length, branch reach and approved mechanical limits against the original installation record.

Can I request a shorter or longer cable?

Submit the required route dimensions. Feasibility, tolerances, optical acceptance and availability outside or between the listed lengths need BWNFiber confirmation.

What should accompany the quotation?

Request the proposed configuration, drawing reference, exceptions, applicable acceptance criteria, available documentation and commercial terms. Agree the missing items before approving the order.

Send the MPO mating-interface reference, eight FC destinations, branch reach, required jacket classification and quantity. Ask BWNFiber to review the configuration and quote the agreed build with its applicable documentation.

Use the page inquiry form and include “Item 24 — OM4 to FC/UPC, eight paths” in your message. Sample arrangements, delivery and MOQ require confirmation.

Image and Schema Handoff

  • No generated product images. Preserve the supplied template gallery positions and insert the user’s prepared photographs after matching the actual product.
  • Proposed image filename: mpo-8f-om4-to-fc-breakout-cable.jpg
  • Main alt, only if the photograph matches: MPO female to eight FC/UPC breakout cable with violet OM4 jacket.
  • Detail alt examples, only if visible: FC/UPC branch connectors and identification labels; MPO connector mating face on an eight-fiber harness.
  • Breadcrumb: Home → Products → Data Center Solutions → MPO Cabling → MPO Breakout & Harness Cable → this product. Confirm real CMS hierarchy before saving.
  • Use Product and BreadcrumbList only with approved facts and actual URL/image. Do not invent MPN, SKU, GTIN, prices, availability, reviews or ratings. A basic Product entity does not establish eligibility for Google’s product rich results.
  • Keep FAQ as visible HTML. Do not add FAQ markup to promise search enhancements.
  • Heading plan: H1 product name; H2 Overview / Features / Specifications / Selection / Applications / Order / Quality / Supplier discussion / FAQ / RFQ; H3 within Selection, Order and FAQ. H4 unnecessary for this content depth.
Related Products

Related Products

Explore additional fiber optic products related to this item and suitable for similar network deployment needs.