1×9 Legacy & Embedded Optical Modules

1×9 Duplex ST Optical Transceiver Module

BWNF-1X9-DUAL-ST is the proposed BWNFiber page identity for a duplex ST optical transceiver in a through-hole 1×9 form factor. It is intended for equipment designs or replacement projects that require two ST fiber ports and a PCB-mounted module rather than a hot-pluggable SFP.

1×9 Legacy & Embedded Optical Modules BWNF-1X9-DUAL-ST Configuration Review

BWNF-1X9-DUAL-ST

Product Value Summary

BWNF-1X9-DUAL-ST is the proposed BWNFiber page identity for a duplex ST optical transceiver in a through-hole 1×9 form factor. It is intended for equipment designs or replacement projects that require two ST fiber ports and a PCB-mounted module rather than a hot-pluggable SFP.

The model name identifies the package family, duplex optical interface, and ST connector. It does not by itself confirm data rate, wavelength, fiber type, reach, supply voltage, electrical interface, temperature grade, pin assignment, optical budget, or standards compliance. Those items must be confirmed against an approved BWNFiber datasheet and the host-board requirements before quotation or production.

Short answer: choose this page only when the host equipment requires a through-hole 1×9 footprint and duplex ST connectivity. If the board uses an SFP cage, a single-fiber BiDi link, or SC/FC receptacles, use the corresponding product family instead.

What Is Fixed and What Must Be Confirmed?

Selection itemCurrent page statusBuyer action
BWNFiber page/model identityBWNF-1X9-DUAL-STConfirm the model appears on the approved quotation and datasheet
Optical interfaceDuplex STConfirm the equipment and patch cords use two ST connections
Package conceptThrough-hole 1×9; not an SFPMatch the PCB footprint and mechanical envelope to an approved drawing
Pin assignment and pin-1 orientationTBC — source requiredProvide the host schematic or legacy module datasheet
Data rate and protocolTBC — source requiredState the required line rate and protocol
Wavelength and fiber typeTBC — source requiredState MMF or SMF, wavelength, and installed-fiber details
Required reach and optical budgetTBC — source requiredProvide link length, connector/splice count, and receiver/transmitter limits
Supply voltageTBC — source requiredConfirm the host rail and permitted tolerance
Electrical I/OTBC — source requiredConfirm PECL, LVPECL, TTL, or other required logic
Operating and storage temperatureTBC — source requiredState the equipment temperature range
Optical performance limitsTBC — source requiredRequire an approved configuration-specific specification
Laser safety, RoHS, and other complianceTBC — source requiredRequest the applicable declaration or report

Key Features

  • Connector-specific page identity: duplex ST.
  • Through-hole 1×9 form-factor positioning for fixed-PCB equipment.
  • Explicit separation from hot-pluggable SFP modules.
  • Configuration review based on the host schematic or the exact legacy part being replaced.
  • Order workflow that locks the electrical, optical, mechanical, and environmental requirements before quotation.
  • Model-specific technical values remain blocked until BWNFiber supplies an approved datasheet or drawing.

Interfaces and Configuration Conditions

Duplex ST optical interface

A duplex link uses separate transmit and receive fibers. Confirm that the installed plant and the equipment ports use ST connectors on both paths. Do not select this page solely because another 1×9 module has the same number of pins; connector type, mechanical outline, pinout, logic levels, power rail, and optical specification must all match.

Through-hole PCB interface

This page is positioned for a module mounted to the host PCB. It is not an SFP and should not be specified for an SFP cage. Before a new layout or a replacement order, compare an approved mechanical drawing and pin assignment with the host board.

Fiber, wavelength, and reach

Fiber type, wavelength, and reach are configuration-dependent. A requested distance alone is insufficient: the buyer should also provide the installed fiber type and the link-loss inputs. BWNFiber must confirm the optical performance for the exact ordered configuration.

How to Select the Correct Configuration

  1. Identify the host footprint. Send the PCB layout, schematic, or the exact legacy part number.
  2. Confirm the connector. Verify that the equipment requires a duplex ST receptacle rather than SC, FC, or a single-fiber BiDi interface.
  3. Define the electrical interface. State the supply rail, logic family, signal-detect requirements, and pin assignment.
  4. Define the optical link. State data rate, protocol, fiber type, wavelength, route length, and the available optical budget.
  5. Define the environment. State the required operating and storage temperature ranges and any equipment-level environmental constraints.
  6. Request controlled documents. Obtain the configuration-specific datasheet, mechanical drawing, pinout, and applicable compliance documents.
  7. Approve before production. Match the final part number and approved specification to the purchase order.

Differences from Related 1×9 Products

Product familyOptical connectionUse it whenDo not assume
BWNF-1X9-DUAL-STTwo fibers; ST interfaceThe host requires duplex ST connectivityThat a rate, wavelength, or pinout is fixed by the family name
BWNF-1X9-DUAL-SCTwo fibers; SC interfaceThe host requires duplex SC connectivityThat the SC and ST mechanics are interchangeable
BWNF-1X9-DUAL-FCTwo fibers; FC interfaceThe host requires duplex FC connectivityThat the FC and ST mechanics are interchangeable
BWNF-1X9-BIDI-STSingle-fiber bidirectional link; ST interfaceThe link must carry both directions over one fiberThat BiDi wavelength pairing matches a duplex design
SFP transceiverHot-pluggable cage and edge connectorThe equipment is designed for SFP modulesThat a soldered 1×9 module can replace an SFP

Application Conditions

Potential applications include legacy communication boards, industrial networking equipment, media converters, and protocol-conversion equipment that were designed around a compatible 1×9 footprint. These are application categories, not compatibility guarantees. Compatibility depends on the exact electrical, optical, mechanical, and environmental requirements of the host.

Technical Specification Status

ParameterBWNF-1X9-DUAL-ST approved value
Form factor and outlineTBC — approved mechanical drawing required
PinoutTBC — approved pin assignment required
Data rate / protocolTBC — configuration-specific source required
Transmit wavelengthTBC — configuration-specific source required
Receive wavelengthTBC — configuration-specific source required
Fiber typeTBC — configuration-specific source required
Maximum reachTBC — configuration-specific source required
Transmit optical powerTBC — approved datasheet or test report required
Receiver sensitivityTBC — approved datasheet or test report required
Receiver overloadTBC — approved datasheet or test report required
Supply voltage and toleranceTBC — approved datasheet required
Electrical input/output levelsTBC — approved datasheet required
Operating temperatureTBC — approved datasheet required
Storage temperatureTBC — approved datasheet required
Compliance and declarationsTBC — applicable evidence required

Testing and Quality-Control Documents

No BWNFiber model-specific test plan or report was supplied for this review. Before this section can be published, the responsible product or engineering owner should confirm:

  • the production test items and acceptance limits;
  • the test conditions and equipment;
  • whether results are recorded per unit, lot, or product family;
  • the applicable laser-safety and material-compliance documents;
  • the document revision linked to the final order code.

Until those records are approved, do not claim a test method, test result, certification, or compliance status on the page.

Packaging and Procurement Information

Packaging method, tray quantity, labeling, moisture or ESD controls, MOQ, price, stock, lead time, warranty, and sample availability are TBC — source required. Confirm them in the quotation rather than presenting an unsupported default on the product page.

Information Required for an RFQ

Send the following information for a configuration review:

  • quantity and project stage;
  • host equipment model and PCB footprint;
  • legacy module manufacturer and exact part number, if this is a replacement;
  • required data rate and protocol;
  • duplex ST connector confirmation;
  • fiber type, wavelength, route length, and optical-budget inputs;
  • supply voltage, electrical logic, pinout, and signal-detect requirements;
  • operating and storage temperature requirements;
  • required datasheet, drawing, test record, and compliance documents;
  • target delivery location and requested schedule.

Primary CTA: Request a BWNF-1X9-DUAL-ST configuration review. Send the host schematic or legacy datasheet with the requirements above. BWNFiber should return a proposed order code and the controlled documents available for that configuration.

Downloads

DocumentStatus
Configuration-specific datasheetTBC — source required
Mechanical drawingTBC — source required
Pin assignmentTBC — source required
Test report or inspection recordTBC — source required
RoHS or other compliance declarationTBC — source required
FAQ

Frequently Asked Questions

Is BWNF-1X9-DUAL-ST an SFP?

No. This page is positioned for a through-hole 1×9 module mounted to a host PCB. It is not intended for an SFP cage or hot-plug workflow.

What does “duplex ST” mean on this page?

It identifies an ST optical interface using separate transmit and receive fibers. The exact optical and electrical configuration still requires confirmation.

Is the data rate fixed by the model name?

No verified rate-specific order code was supplied for this review. State the required data rate and protocol in the RFQ and request a configuration-specific datasheet.

Can I select the module by distance alone?

No. Fiber type, wavelength, transmitter output, receiver limits, connector and splice losses, and engineering margin all affect the link. Provide the link inputs for review.

Can it replace any nine-pin optical module?

No. The pin count alone does not prove compatibility. Check the footprint, pinout, supply, logic levels, mechanical outline, connector, and optical specification.

What should I provide for a legacy replacement?

Provide the legacy manufacturer, exact part number, datasheet, host schematic, board photographs, and required operating conditions. Remove customer-confidential information before sharing files.

Are 3.3 V and 5 V versions available?

TBC — source required for BWNF-1X9-DUAL-ST. Confirm the host rail and request the matching approved configuration.

Is an industrial-temperature version available?

TBC — source required. State the required temperature range and ask BWNFiber to confirm an approved order code.

Is the product RoHS compliant?

TBC — source required. Request the applicable declaration for the exact ordered configuration.

What documents should be approved before ordering?

Approve the final part number, configuration-specific datasheet, mechanical drawing, pin assignment, and any required compliance or inspection documents before production.

Related Products

Related Products

Explore additional fiber optic products related to this item and suitable for similar network deployment needs.