1×2 75/25 Unbalanced Mini PLC Splitter, 0.9 mm SC/APC

BWN-PLC-MMST-1X2-SC-APC-0.9-U7525

This connectorized 1×2 mini PLC splitter divides one single-mode input into labeled 75% and 25% outputs. The photographed sample uses SC/APC connectors, G.657.A1 0.9 mm fiber and a 60 × 7 × 4 mm package. Use the ratio-specific loss limits for each output; do not substitute an even 1×2 table or an 85/15 product sheet.

Primary CTA: Send the required ratio, connector, pigtail length, quantity and document pack for configuration review and quotation.

Quick answer for buyers

The 75% output is the lower-loss path and the 25% output is the higher-loss path on this unequal 1×2 build. The photographed test sheet lists maximum insertion loss of 2.3 dB for the 75% port and 7.5 dB for the 25% port. Confirm the port labels, exact order code and revision-controlled datasheet before approving the BOM or closing the link budget.

Verified configuration

Port map and optical limits for the photographed build

Do not infer direction, cascade position or network compatibility from the ratio alone. The network designer must assign each labeled output to a route using the approved optical budget.

Sample-specific measured results

The values below are transcribed from the photographed test sheet for sample serial 25120100009, inspected on 2025-12-01. They are evidence for that sample, not a promise that every production unit will have identical measured values.

The sheet also lists directivity above 55 dB. Publication of the serial number and measured data requires QA/Marketing approval.

How to confirm this model before ordering

1. State 1×2 and the nominal 75/25 ratio.
2. Confirm which route must receive the 75% port and which must receive the 25% port.
3. Confirm SC/APC for the input and both outputs.
4. Confirm G.657.A1, 0.9 mm construction and the required pigtail length.
5. Check that the host tray or enclosure can accept the 60 × 7 × 4 mm package and manage the pigtails without violating the approved bend-control plan.
6. Define the maximum permitted loss for each path; do not use an even-split 1×2 limit.
7. Request the revision-controlled datasheet, drawing and unit/batch test report required by the project.

Fit and non-fit conditions

This build may be considered when an approved host enclosure can protect and route a compact connectorized mini module and when the design specifically calls for unequal 75/25 optical division.

Do not approve it when:

• the design calls for equal 50/50 division or a different unequal ratio;
• the adapter/interface is not SC/APC;
• the host cannot protect the 0.9 mm fibers or provide adequate routing clearance;
• the link budget does not accept the separate 75% and 25% path limits;
• the project requires a standard, certification, package rating or environmental qualification that has not been confirmed for this SKU.

Differences from related products

For a wider product-family route, use the fiber optic splitter portfolio rather than expanding this exact-SKU page into a general buying guide.

Documents to request before approval

• Revision-controlled product datasheet — TBC
• Dimensional drawing with fiber exits — TBC
• Order-code/model confirmation — TBC
• Unit or batch optical test report — sample image available; publication approval TBC
• Applicable standards/compliance declaration — TBC, if required
• Packaging and label specification — TBC

RFQ information

Send:

• quantity;
• 1×2, 75/25 ratio string;
• the route assigned to each labeled output;
• SC/APC interface requirement;
• 0.9 mm fiber and required input/output lengths;
• host enclosure/tray and available package clearance;
• maximum permitted loss for each route;
• required datasheet, drawing, test-report and compliance documents;
• packaging, labeling and delivery requirements.

BWNFiber should return the confirmed public model code, revision-controlled specification, quotation and available evidence pack. This return scope is TBC pending Sales/Product Owner approval.