CWDM & DWDM Optical Transceivers

1.25G CWDM SFP 80 km Duplex LC Transceiver

Use this model as a candidate for a 1.25 Gb/s duplex-fiber CWDM link when the design calls for an 80 km-class SFP and the selected wavelength is compatible with the CWDM mux/demux plan. It should not be approved from reach alone. The engineering review must confirm the two endpoint modules, nominal channel, fiber route, passive WDM loss, connector and splice loss, design margin, receive sensitivity and maximum permitted receive power.

CWDM & DWDM Optical Transceivers BWNF-GE-CXXL-80D Configuration Review

BWNF-GE-CXXL-80D

What This Model Is For

Use this model as a candidate for a 1.25 Gb/s duplex-fiber CWDM link when the design calls for an 80 km-class SFP and the selected wavelength is compatible with the CWDM mux/demux plan. It should not be approved from reach alone. The engineering review must confirm the two endpoint modules, nominal channel, fiber route, passive WDM loss, connector and splice loss, design margin, receive sensitivity and maximum permitted receive power.

Key Features

  • Exact-model identity: BWNF-GE-CXXL-80D.
  • 1.25 Gb/s CWDM SFP form factor.
  • Duplex LC optical interface for single-mode fiber.
  • Legacy source lists 1270–1610 nm CWDM wavelength choices.
  • 80 km nominal reach class, subject to the approved link-loss calculation.
  • CWDM DFB transmitter and PIN receiver.
  • DDM/DOM is listed in the source record; exact diagnostic fields remain subject to the approved datasheet.
  • Commercial operating case temperature listed as 0–70 °C.

Interfaces and Fiber Configuration

Selection itemWhat is supported nowWhat the buyer must confirm
Host electrical interfaceSFP form factorExact switch/router model, port support, EEPROM coding and vendor policy
Optical connectorDuplex LCPatch-cord connector and polish at both ends; the exact source does not state UPC/APC
Fiber mediumSingle-mode fiberFiber type, route length, attenuation by wavelength, connector/splice count and WDM loss
CWDM channel1270–1610 nm range in the legacy recordExact nominal channel and order suffix approved by BWNFiber
DiagnosticsDDM/DOM listedRequired readings, thresholds, calibration method and host display support

Compatibility Is Conditional

This draft does not claim universal compatibility with Cisco, Juniper, HPE, MikroTik or any other platform. A brand name alone is not enough to approve a module. Send the exact host manufacturer, chassis or appliance, line card, port type, operating system/version where relevant, and any required vendor part-number mapping. BWNFiber should return the approved EEPROM code and compatibility evidence for that exact host before release.

How to Select and Approve the Correct Configuration

  1. Lock both endpoints. Record the host and port at each end, not just the network brand.
  2. Choose one CWDM channel. Match the transmit wavelength to the mux/demux channel plan and the corresponding module at the far end.
  3. Calculate the worst-case optical path. Include fiber attenuation at the selected wavelength, mux/demux insertion loss, connectors, splices, patch panels and an engineering margin.
  4. Check both receive limits. The calculated receive power must remain above receiver sensitivity and below receiver overload. Receiver overload is currently TBC — source required for this model.
  5. Confirm temperature and power. The supported source currently covers 0–70 °C and less than 1.0 W only. Other grades require written evidence.
  6. Approve the document set. Obtain the current BWNFiber datasheet, channel/order-code table, compatibility statement and agreed test-report format before the PO is released.

80 km Is a Reach Class, Not a Link Guarantee

The module’s nominal reach does not prove that every 80 km route will work. Actual feasibility depends on the selected wavelength, fiber attenuation, passive CWDM components, connector and splice losses, transmitter output, receiver sensitivity, receiver overload and design margin. Do not approve the link from route length alone. Use the exact-model limits and the project’s measured or specified path loss.

Related BWNFiber Reach Variants

The local upload inventory also contains planned 1.25G CWDM SFP records for 20 km, 40 km and 120 km reach classes. These are separate model records, not interchangeable labels. Select the shortest reach class that satisfies the approved loss budget and receiver limits, then verify the exact source sheet for that model. Do not copy optical limits from one reach variant to another.

Applications — Subject to System Approval

  • Point-to-point 1.25 Gb/s CWDM links over duplex single-mode fiber.
  • CWDM access or metro links using a compatible passive mux/demux channel.
  • Switch-to-switch or router uplinks where the host accepts the approved SFP coding and power class.
  • Capacity expansion on an existing duplex-fiber route after wavelength plan and loss-budget validation.

These are application categories, not a claim that every host, protocol or route is compatible.

Testing and Quality-Control Requirements

The supplied exact-model record does not establish BWNFiber’s current production test method or report format. Before publication or purchase, BWNFiber product engineering should confirm which of the following are performed and what evidence can be supplied:

  • Part-number, label and wavelength verification.
  • Transmit power and receive-sensitivity test conditions.
  • Optical spectrum and center-wavelength verification.
  • DDM/DOM reading verification and calibration tolerance.
  • Host compatibility or EEPROM-code verification against the named platform.
  • Temperature screening, burn-in or environmental testing, if offered.
  • Serial-number traceability and the format of any test report.

All items above remain TBC — source required until a current controlled document is attached.

Packaging and Procurement Information

ItemStatus
MOQTBC — source required
Unit priceTBC — quotation required
Stock statusTBC — source required
Lead timeTBC — source required
WarrantyTBC — source required
Packaging quantity and ESD protectionTBC — source required
Label / OEM optionsTBC — source required
Country-specific conformity documentsTBC — source required

What to Include in the RFQ

Send the following in one request so sales and engineering can review the same configuration:

  • Model: BWNF-GE-CXXL-80D.
  • Required CWDM wavelength/channel at each endpoint.
  • Exact host manufacturer, chassis/appliance, line card and port.
  • Required EEPROM/vendor coding or reference OEM part number.
  • Route length and worst-case optical-loss calculation.
  • CWDM mux/demux model and insertion loss for the selected channel.
  • Fiber type, connector/splice count and patch-panel path.
  • Operating case-temperature requirement.
  • Quantity, sample/pilot requirement and delivery destination.
  • Required datasheet, compatibility statement, test report and conformity documents.

Primary CTA: Request the Exact-Model Datasheet and Compatibility Review.

CTA helper text: Send the wavelength, two endpoint host models, route-loss worksheet, temperature requirement and quantity. BWNFiber can then confirm which fields are supported and which still require engineering approval.

Downloads — Release Only After Approval

  • BWNF-GE-CXXL-80D datasheet: TBC — source required
  • Wavelength and order-code table: TBC — source required
  • Host compatibility statement: TBC — source required
  • Test-report sample: TBC — source required
  • Product drawing and label artwork: TBC — source required
FAQ

Frequently Asked Questions

Is BWNF-GE-CXXL-80D a 1.25G CWDM SFP?

The supplied migration record maps legacy model YXF-GE-CXXL-80D to BWNF-GE-CXXL-80D, and the exact legacy product page lists a 1.25 Gb/s CWDM SFP. BWNFiber product engineering must still approve the current BWNFiber-controlled datasheet before publication.

Does the module support every wavelength from 1270 to 1610 nm at once?

No. The range describes available CWDM channel versions. The order must specify one nominal transmit wavelength that matches the CWDM mux/demux channel plan and the far-end design.

Is an 80 km route guaranteed to work?

No. Eighty kilometres is a nominal reach class. The link must pass a worst-case optical-loss and receiver-limit review that includes fiber, mux/demux, connectors, splices, patch panels and design margin.

Can this module be used on a short link?

Only after the expected receive power is checked against the module’s maximum receiver input. The current exact-model source does not provide the overload limit, so short-link approval is blocked until that value is supplied.

Which fiber and connector does it use?

The exact legacy record lists single-mode fiber and a duplex LC interface. Fiber grade and connector polish are not confirmed in the supplied source and must be stated in the order specification.

Does it support DDM or DOM?

DDM/DOM is listed in the exact legacy record. The current BWNFiber datasheet must confirm the monitored parameters, calibration method, alarm thresholds and host support.

Is it compatible with my Cisco, Juniper, HPE or MikroTik switch?

Compatibility cannot be approved from the brand name alone. Provide the exact host, line card, port and required coding. Ask for written confirmation tied to that configuration.

What temperature grade is supported?

The available exact-model source lists a 0–70 °C operating case range. An industrial or extended-temperature option is TBC — source required.

Is the module compliant with SFP MSA, SFF-8472 or RoHS?

These claims are common on competitor pages, but the supplied exact-model BWNFiber evidence does not prove them. Publish them only after BWNFiber provides the current declaration or controlled datasheet.

What documents should be requested before a bulk order?

Request the current model datasheet, wavelength/order-code table, host-compatibility statement, agreed test-report format, product drawing/label, packaging specification and any project-required conformity documents.

Related Products

Related Products

Explore additional fiber optic products related to this item and suitable for similar network deployment needs.